Standards and Service Limits
|
2-14 | ||||||
| Item | Measurement | Qualification | Standard or New | Service Limit | ||
| Reverse idler gear | Reverse idler gear shaft diameter at needle bearing contact area | 13.990-14.000 mm
(0.5508-0.5512 in.) |
When worn or damaged | |||
| I.D. | 18.007-18.020 mm
(0.7089-0.7094 in.) |
When worn or damaged | ||||
| End play | 0.05-0.18 mm (0.002-0.007 in.) | - | ||||
| I.D. of reverse idler gear shaft holder | 14.416-14.434 mm
(0.5676-0.5683 in.) |
When worn or damaged | ||||
| Sub-shaft | Diameter of needle bearing contact area | at transmission housing | 25.991-26.000 mm
(1.023-1.024 in.) |
When worn or damaged | ||
| at 4th gear collar | 23.9935-23.0065 mm
(0.9446-0.9058 in.) |
When worn or damaged | ||||
| 4th gear I.D. | 32.000-32.016 mm
(1.2600-1.2605 in.) |
When worn or damaged | ||||
| 4th gear end play | 0.05-0.17 mm
(0.002-0.007 in.) |
- | ||||
| 4th gear collar length | 24.0-24.1 mm
(0.945-0.949 in.) |
- | ||||
| 4th gear collar flange thickness | 2.95-3.10 mm
(0.116-0.122 in.) |
When worn or damaged | ||||
| 4th gear thrust washer thickness | 2.93-3.00 mm
(0.115-0.118 in.) |
When worn or damaged | ||||
| 1st-clutch feed pipe O.D. | at 15 mm (0.6 in.) from end | 7.97-7.98 mm
(0.3138-0.3142 in.) |
7.95 mm (0.313 in.) | |||
| Item | Measurement | Qualification | Standard or New | |||
| Wire Diameter | O.D. | Free Length | No. of Coil | |||
| Main valve body springs, refer to the '01 Civic Shop Manual on this CD (see page 14-183) | Relief valve spring | 1.1 mm
(0.043 in.) |
8.6 mm
(0.339 in.) |
37.1 mm
(1.4161 in.) |
13.4 | |
| Modulator valve spring | 1.4 mm
(0.055 in) |
9.4 mm
(0.370 in.) |
33.8 mm
(1.331 in.) |
10.9 | ||
| CPB valve spring | 1.0 mm
(0.039 in.) |
8.1 mm
(0.319 in.) |
40.9 mm
(1.610 in.) |
16.2 | ||
| 1-2 shift valve spring | 0.9 mm
(0.035 in.) |
7.6 mm
(0.299 in.) |
41.3 mm
(1.626 in.) |
16.3 | ||
| 2nd orifice control valve spring | 0.7 mm
(0.028 in.) |
6.6 mm
(0.260 in.) |
34.8 mm
(1.370 in.) |
22.0 | ||
| Servo control valve spring | 1.0 mm
(0.039 in.) |
8.1 mm
(0.319 in.) |
52.1 mm
(2.051 in.) |
20.8 | ||
| Regulator valve body springs, refer to the '01 Civic Shop Manual on this CD (see page 14-186) | Stator reaction spring | 4.5 mm
(0.177 in.) |
35.4 mm
(1.394 in.) |
30.3 mm
(1.193 in.) |
1.9 | |
| Regulator valve spring A | 1.9 mm
(0.075 in.) |
14.7 mm
(0.579 in.) |
77.4 mm
(3.047 in.) |
15.2 | ||
| Regulator valve spring B | 1.8 mm
(0.071 in.) |
9.6 mm
(0.378 in.) |
44.0 mm
(1.732 in.) |
12.6 | ||
| Cooler relief valve spring | 1.0 mm
(0.039 in.) |
8.4 mm
(0.331 in.) |
33.8 mm
(1.331 in.) |
8.2 | ||
| Torque converter check valve spring | 1.0 mm
(0.039 in.) |
8.4 mm
(0.331 in.) |
33.8 mm
(1.331 in.) |
8.2 | ||
| Lock-up control valve spring | 0.8 mm
(0.031 in.) |
6.0 mm
(0.236 in.) |
38.4 mm
(1.512 in.) |
30.3 | ||