Item |
Measurement |
Qualification |
Standard or New |
Service Limit |
Parking brake lever |
Distance travelled when pulled with 196 N (20 kgf, 44 lbs) of force |
|
8-9 clicks |
Brake pedal |
Pedal height (Carpet removed) |
M/T |
180 mm (7.09 in.) |
A/T |
184 mm (7.24 in.) |
Free play |
|
0.4-3.0 mm (0.016-0.118 in.) |
Master cylinder |
Piston-to-pushrod clearance |
|
0-0.4 mm (0-0.02 in.) |
Brake disc |
Thickness |
Front |
20.9-21.8 mm (0.82-0.86 in.) |
19.0 mm (0.75 in.) |
Rear |
8.9-9.1 mm (0.350-0.358 in.) |
8.0 mm (0.31 in.) |
Runout |
|
- |
0.10 mm (0.004 in.) |
Parallelism |
|
- |
0.015 mm (0.0006 in.) |
Brake pads |
Thickness Front |
|
9.0-10.0 mm (0.35-0.39 in.) |
1.6 mm (0.06 in.) |
Thickness Rear |
|
8.5-9.5 mm (0.33-0.37 in.) |
1.6 mm (0.06 in.) |
Brake drum |
I.D. |
|
219.9-220.0 mm (8.657-8.661 in.) |
221 mm (8.701 in.) |
Brake shoes |
Lining thickness |
|
4.5 mm (0.18 in.) |
2.0 mm (0.08 in.) |
Brake booster Vehicle with ABS |
Characteristics at 196 N (20 kgf, 44 lbf) pedal force |
Vacuum |
N (kgf, lbf) |
kPa (kgf/cm2, psi) |
kPa (mmHg, inHg) |
0 (0, 0) |
98 (10, 22) |
0 (0, 0) |
294 (30, 66) |
1700 (17, 240) |
66.7 (500, 19.7) |
98 (10, 22) |
4600 (47, 670) |
294 (30, 66) |
10500 (107, 1500) |
Brake booster Vehicle without ABS |
Characteristics at 196 N (20 kgf, 44 lbf) pedal force |
Vacuum |
N (kgf, lbf) |
kPa (kgf/cm2, psi) |
kPa (mmHg, inHg) |
0 (0, 0) |
98 (10, 22) |
0 (0, 0) |
294 (30, 66) |
1700 (17, 240) |
66.7 (500, 19.7) |
98 (10, 22) |
4400 (17, 640) |
294 (30, 66) |
10500 (107, 1500) |
Item |
Measurement |
Qualification |
Standard or New |
Refrigerant |
Type |
|
HFC-134 a (R-134 a) |
Capacity or system |
|
500-550 g (17.6-19.4 oz) |
Refrigerant Oil |
Type |
|
SANDEN: SP-10 (P/N 38897-P13-003 or38899-P13-A01) |
Capacity of components |
Condenser |
25 ml (5/6 fl oz, 0.9 Imp oz) |
Evaporator |
45 ml (1 ½ fl oz, 1.3 Imp oz) |
Each line and hose |
10 ml (1/3 fl oz, 0.4 Imp oz) |
Receiver |
10 ml (1/3 fl oz, 0.4 Imp oz) |
Compressor |
130-150 ml (4 1/3 fl oz, 3.7 Imp oz-5 fl oz, 4.5 Imp oz) |
Compressor |
Starter coil resistance |
at 68°F (20°C) |
3.05-3.35 ohms |
Pulley-to-pressure plate clearance |
|
0.5+0.15 mm (0.02+0.006 in.) |
Compressor belt NOTE: Adjust a new belt to the new belt spec., run the engine for 5 minutes, then readjust it to the used belt spec. |
Deflection with 98 N (10 kgf, 22 lbs) applied mid-way between pulleys |
|
Used belt: 8.5-11.0 mm (0.33-0.43 in.) |
New belt: 5.0-6.5 mm (0.20-0.26 in.) |
Tension (measured with belt tension gauge) |
|
Used belt: 440-590 N (45-60 kgf, 100-130 lbs) |
New belt: 930-1,125 N (95-115 kgf, 210-255 lbs) |